• <button id="66kmq"><dl id="66kmq"></dl></button>
    <table id="66kmq"></table>
  • <li id="66kmq"></li>
  • <code id="66kmq"></code>
  • <code id="66kmq"></code>
    歡迎來Nano電子商城!
    您好 [請登錄]   [免費注冊]
    x
    全部商品分類

    Palas Promo 2000氣溶膠粒徑譜儀原版手冊

    The objective that has to be achieved hereby is to change the velocity (preset velocity) to the meas
    下載次數:629 瀏覽次數:995發布時間:2018-12-21 19:26
    允許查看的會員等級:非會員   普通會員   高級會員   VIP會員   

    文檔詳情

    4.1 How to calibrate your sensor for the selected measurement range with CalDust1100?

    To run the calibration procedure, connect a flexible tube to the aerosol inlet of the sensor. Hold

    the free end of the flexible tube into the opening of the supplied CalDust 1100 container after

    shaking the container to loosen the particles and make them air‐borne inside the container. By

    doing so you provide that the air which is sucked into the sensor is primarily filled with particles of

    a diameter of 0.85 μm. You must not shake too strongly as you must not have more than 10 %

    coincident signals during the calibration procedure.  

    Calibration of the photomultiplier (PM) amplification:

    The objective that has to be achieved hereby is to adjust the PM‐amplification (DAC) so that the

    target channel of calibration matches the measured maximum of the raw data distribution. In‐

    creasing/decreasing the PM‐amplification by increasing/decreasing the voltage will move the

    measured maximum (channel of calibration) upward/downward. 

    4.2 Calibration of the velocity:

    The objective that has to be achieved hereby is to change the velocity (preset velocity) to the

    measured velocity. You measure the velocity by moving the red cross into the right maximum

    within the time chart. If the gas density of your measured aerosol doesn't change you do not have

    to calibrate the velocity. However, during a calibration procedure one should always compare the

    old particle velocity with the new particle velocity as a large deviation gives also an indication for a

    leakage in your suction tubes or a problem with your suction pump. In case you have a pressure‐

    resistant sensor, e.g. welas? sensor 2070 P, or a pressure‐resistant and heatable sensor, e.g. we‐

    las? sensor 2070 HP, and if the pressure or temperature conditions change, you have to calibrate

    and adjust the particle velocity as well. Always try to calibrate your sensor with CalDust 1100 at

    the same pressure and temperature conditions as your subsequent measurements. However,

    sometimes it is not possible to calibrate your sensor with a calibration dust at the same thermo‐

    dynamic conditions. For this reason, you can also adjust the velocity without re‐adjusting the pho‐

    tomultiplier amplification and without using a calibration dust. However, the particles have to be

    larger than 0.4 μm. If you adjust the PM amplification, the velocity should not change. Alternative‐

    ly you can activate the automated gas density correction.

    我們營業的時間9:00-18:00

    • 技術
    關閉在線客服

    Nano電子商城微信公眾號手機商城 Nano電子商城微信公眾號二維碼

    手機商城           微信商城

    任何購物問題請聯系納米科技(香港)有限公司  | 江蘇省蘇州市昆山開發區章基路189號科創基地2號樓202室 Tel:021-52069907 email: 19mro@19mro.com

    工作時間:周一至周五 8:00-18:00; 網站備案號 :滬ICP備12049383號; Copyright?2009-2012 19mro.com 版權所有 


     
    韩国三级中文字幕hd久久精品| 国产AV无码专区亚洲AV毛网站| 精品国产a∨无码一区二区三区| 亚洲AV中文无码乱人伦在线观看| 日韩精品无码免费一区二区三区| 日韩乱码人妻无码中文视频| 亚洲va中文字幕无码| 无码精品人妻一区二区三区人妻斩 | 在线天堂中文WWW官网| 国产拍拍拍无码视频免费| 岛国无码av不卡一区二区| 欧美日韩中文字幕久久伊人| 黑人无码精品又粗又大又长| 水蜜桃av无码一区二区| 亚洲欧洲日产国码无码久久99 | 一级中文字幕免费乱码专区| 国产精品中文久久久久久久| 国产亚洲精久久久久久无码AV | 免费A级毛片无码视频| 亚洲国产a∨无码中文777| 最近免费字幕中文大全| 中文字幕性| 直接看的成人无码视频网站| 最近2019免费中文字幕6| 色综合中文综合网| 久久久久久久久久久久中文字幕 | 亚洲色中文字幕无码AV| 最近中文字幕在线中文视频| 亚洲人成影院在线无码观看| 国产精品无码DVD在线观看| 人妻无码视频一区二区三区| 无码人妻一区二区三区在线视频| 色偷偷一区二区无码视频| 久久99精品久久久久久hb无码| 色综合久久无码中文字幕| 精品日韩亚洲AV无码| 4444亚洲人成无码网在线观看| 99精品一区二区三区无码吞精| 国产福利电影一区二区三区久久老子无码午夜伦不 | 内射无码专区久久亚洲| 久久精品无码一区二区日韩AV|